Streaks on glass do not appear by magic or because of a "bad" window. They are caused by dust particles, detergent residues, and mineral deposits that turn into cloudy streaks, white spots, and greasy film upon drying. In its recommendations, cleaning equipment manufacturer Kärcher highlights three factors that determine the result: glass temperature, detergent dosage, and the condition of tools. These three variables are most often the reason why even a thorough wash ends up requiring a wipe-down.

The sun is not an ally, but the main enemy of clean glass

It would seem that a clear day is the ideal time for washing windows: all dirt is clearly visible, and it seems the result will be impeccable. In practice, direct sunlight heats the glass, and the water mixed with detergent solution evaporates too quickly. One physically cannot remove the moisture evenly, and streaks of detergent and mineral impurities remain on the surface. Kärcher recommends choosing dry, cloudy weather or washing windows while they are in the shade. The paradox is that the result looks cleaner on a cloudy day because the glass does not overheat, and the solution can be removed before it dries completely.

Excess detergent: more is not better

The desire to make the cleaning solution "stronger" often works against purity. An excess of household chemicals leaves a thin film on the glass, which appears as cloudy spots, greasy streaks, or uneven shine after drying. This problem is especially typical for those who use regular dish soap but add much more than necessary. The correct approach is a minimal effective dosage: a small amount of concentrate per liter of water is enough for the solution to wet the surface without leaving a sticky film. If the glass "attracts" dust after washing or feels slightly greasy to the touch, it is a sure sign of using too much detergent.

Dirty cloth and incorrect sequence

Dust, street grime, and small sand particles accumulate on window frames, joints, and sills. If you move on to the glass using the same cloth after cleaning the frames, all this dirt is transferred to the clean surface. Furthermore, a cloth already saturated with dirty water loses its absorbency and begins to leave marks. Therefore, you should prepare a separate clean microfiber cloth for the glass, and clean the frames, joints, and sills before starting to wash the double-glazed unit. In its recommendations, the Australian Glass and Glazing Association also notes that before wiping, the glass must be moistened with a sufficient amount of clean water or detergent solution to remove loose dirt: dry wiping not only fails to solve the problem but also spreads particles across the entire surface, and individual hard inclusions can leave micro-scratches.

Hard water and forgotten edges

Even if all previous steps are followed correctly, simply waiting for the window to dry can ruin the result. Along with the water, dissolved mineral substances—calcium and magnesium salts, especially typical for hard tap water—remain on the glass. After evaporation, they form light spots and streaks. Therefore, after washing, it is necessary to remove excess moisture with a squeegee or a clean dry cloth, not forgetting the edges of the glass where drops usually accumulate. If the water in the region is hard, it makes sense to use filtered or distilled water for final wetting—this significantly reduces the amount of mineral deposits.

Worn squeegee: the invisible source of streaks

A squeegee is a tool that helps to remove water from the glass quickly, but only if its rubber blade is even and clean. Over time, the rubber wears out, irregularities appear on it, and small particles of dirt stick to the edge. As a result, the tool leaves thin parallel streaks on the glass, which cannot be removed without re-washing. Kärcher recommends regularly cleaning the rubber blade, checking it for sand or other dirt before each cleaning, and replacing it when the rubber deforms. This is arguably the most underestimated element of the whole process: even an ideal solution and a clean microfiber cloth will not help if the blade leaves marks.

Following the sequence—from cleaning the frames to final edge wiping—allows you to avoid returning to the same window multiple times. None of the listed errors is critical on its own, but in combination, they turn a routine chore into an endless cycle of "washed, wiped, saw streaks, washed again." Understanding the physics of the process—evaporation speed, surface tension, mineral deposits—helps in choosing the right conditions and tools to get transparent glass the first time.